Car Lifts
BAOHUA BH6108 4T In-Ground Wheel Alignment Scissor Lift
Model: BH6108
A 4,000 kg in-ground wheel alignment scissor lift with 4,500 mm runways, a 3,000 kg secondary lift and 1,850 mm main lifting height for automotive service bays.
- Minimum order
- 1 set
- 4,000 kg main lift and 3,000 kg secondary lift
- 4,500 x 630 mm runways
- 1,850 mm main and 500 mm secondary lifting heights
- Adjustable front turnplate positions and rear slip plates
- Recessed installation with independent 24 V controls
Final configuration, specifications, accessories, packaging, and delivery terms are confirmed in the quotation.
Product overview
The BAOHUA BH6108 is a 4-ton in-ground wheel alignment scissor lift for automotive alignment, inspection and maintenance bays. Two 4,500 mm-long, 630 mm-wide runways support compatible vehicles up to a total rated load of 4,000 kg. The main lift reaches a maximum lifting height of 1,850 mm.
An integrated secondary scissor lift provides a separate 3,000 kg lifting capacity and 500 mm lifting height. Its platform length is adjustable from 1,520 to 1,820 mm. Vehicle lifting points, support positions and load distribution must match the final lift configuration and operating instructions.
The alignment runways include adjustable front turnplate positions and rear slip plates. Confirm the required turnplates and wheel alignment measurement system in the quotation. Mechanical lock teeth, a pneumatic cylinder and an independent 24 V control unit are shown in the product documentation. The electro-hydraulic drive uses a 2.2 kW motor.
Recessed installation places the lift bases in two prepared floor pits. The supplied foundation plan specifies each pit at 4,650 mm long, 680 mm wide and 330 mm deep, with 850-950 mm clear spacing between pits, at least 200 mm of concrete beneath the pit floor and a 100 mm conduit. A 7,000 x 4,000 mm bay is suggested in that plan. These are planning references; confirm the final factory drawing and site conditions before civil work.
For a quotation, send vehicle weights, wheelbases and track widths, your alignment-system layout, available workshop space, electrical supply, quantity and destination. BAOHUA can then confirm the lift configuration, accessories and installation requirements for your project.
TECHNICAL DATA
Specifications
Values below follow the supplied product listing. Confirm the final selected configuration before ordering.
Product specifications
| Model | BH6108 |
|---|---|
| Product Type | In-ground wheel alignment scissor lift |
| Main Lifting Capacity | 4000 kg |
| Secondary Lifting Capacity | 3000 kg |
| Maximum Lifting Height | 1850 mm |
| Secondary Lifting Height | 500 mm |
| Runway Length | 4500 mm |
| Runway Width | 630 mm per runway |
| Secondary Platform Length | 1520-1820 mm |
| Motor Power | 2.2 kW |
| Power Supply | 220 V / 380 V; confirm phase and frequency before ordering |
| Control Voltage | 24 V |
| Drive System | Electro-hydraulic |
Installation requirements
Plan two pits, each 4650 x 680 x 330 mm (L x W x D), with 850-950 mm clear spacing. The supplied plan specifies concrete thickness of at least 200 mm below the pit floor, a 100 mm pre-buried conduit and control-unit routing of no more than 3000 mm. Suggested bay size: 7000 x 4000 mm. Confirm the final factory drawing, foundation suitability, vehicle approach, clearances, electrical phase/frequency and compressed-air requirements before construction.
PRODUCT DETAILS
Features, construction, and applications
Review the available product detail images for the selected equipment.
View 3 more detail images
PRODUCT VIDEO
See the equipment in detail
Play the product video directly on this page.
MODEL SELECTION
How to choose this equipment
Selection guidance
- Vehicle fit and two lifting capacities
- Check vehicle mass and axle loading against the 4000 kg main-lift rating. Check approved lifting points and load distribution separately for the 3000 kg secondary lift.
- Alignment equipment and runway geometry
- Match vehicle wheelbase and track width to the 4500 x 630 mm runways. Confirm turnplates, rear slip plates and the layout of the selected alignment measurement system.
- Foundation and workshop utilities
- Review the final pit drawing with the installer before excavation. Confirm the 220 V or 380 V supply option, phase, frequency, air supply and access around the lift.
BUYER SEARCH GUIDE
Wheel-alignment scissor lift sourcing guide
This lift type supports wheel alignment, chassis inspection, suspension adjustment, tire service, and repair-bay work for compatible vehicles.
Common sourcing language
Importers, distributors, and workshop buyers may describe BAOHUA BH6108 4T In-Ground Wheel Alignment Scissor Lift using these related terms:
- wheel alignment scissor lift
- alignment rack lift
- hydraulic alignment car lift
- in-ground alignment lift
What to compare before ordering
Alignment-lift buyers usually compare rated capacity, platform dimensions, turn-plate and slip-plate provision, secondary lift, runway synchronization, minimum height, lifting height, and installation depth. The vehicle wheelbase range and wheel-alignment machine layout should be checked together.
View Car Lifts
Compare related models and choose the configuration that matches your vehicles, process, utilities, and workshop layout.
View categoryBUYER FAQ
BH6108 in-ground wheel alignment scissor lift FAQ
Review the confirmed product data and the project information needed before requesting a final configuration.
What are the main and secondary lifting capacities?
The main lift is rated at 4000 kg. The integrated secondary lift is rated separately at 3000 kg. Vehicle support positions and load distribution must follow the final equipment instructions.
What are the runway dimensions and lifting heights?
Each main runway is 4500 mm long and 630 mm wide. Maximum main lifting height is 1850 mm. The secondary lift has 500 mm lifting height and a 1520-1820 mm platform length.
Does this wheel alignment lift need floor pits?
Yes. The in-ground configuration uses two prepared pits. The supplied reference plan shows each pit as 4650 x 680 x 330 mm with 850-950 mm clear spacing. Confirm the final factory drawing before construction.
What alignment features are included in the product design?
The runways have adjustable front turnplate positions and rear slip plates. Confirm the supplied turnplates and the separate alignment measurement system in your quotation.
What electrical supply does the BH6108 use?
The product sheet lists a 2.2 kW electro-hydraulic drive, a 24 V control system and 220 V / 380 V supply options. Confirm the required phase, frequency and compressed-air supply before ordering.
What information should I send for a quotation?
Send vehicle weights, wheelbases and track widths, alignment-system details, available bay space, the pit plan, electrical supply, quantity and delivery destination.