Car Lifts
BAOHUA 6018C 4T Ultra-Thin Wheel Alignment Scissor Lift
Model: 6018C
A 4-ton surface-mounted wheel alignment scissor lift with 4500 mm runways, front turnplates, rear slip plates and an optional rolling jack for wheel-free service.
- Minimum order
- 1 set
- Lifting Capacity: 4000 kg
- 4500 x 630 mm runways
- Surface-mounted ultra-thin design
- Front alignment turnplates and rear slip plates
- Optional rolling jack for wheel-free service
Final configuration, specifications, accessories, packaging, and delivery terms are confirmed in the quotation.
Product overview
The BAOHUA 6018C is a 4-ton ultra-thin wheel alignment scissor lift for passenger-car service workshops. Its surface-mounted layout combines two 4500 mm-long, 630 mm-wide runways with an electro-hydraulic lifting system. The 4000 kg rating applies to the main lift.
Front alignment turnplates and rear slip plates support wheel alignment workflows. Match the vehicle wheelbase, track width and tire positions to the runway layout, and check compatibility with your alignment measurement system. The alignment machine, targets and wheel clamps are separate equipment unless specified in the quotation.
An optional rolling bridge jack travels along the inner runway rails and provides wheel-free access for suitable tire, brake and suspension work. Order this accessory when secondary lifting is required. Its capacity and lifting range must match the selected jack configuration and approved vehicle lifting points.
The lift uses a 2.2 kW electro-hydraulic drive, an independent control cabinet and a 24 V control system with a limit-switch device. The product documentation lists 220 V and 380 V supply options. Specify the required voltage, phase and frequency before ordering.
For workshop planning, check the approach ramps, vehicle ground clearance, working space around the lift and overhead clearance. Obtain the final installation drawing and confirm concrete and anchoring requirements with the installer. Send your vehicle range, bay dimensions, alignment-system details, power supply, accessory requirements, quantity and destination for a tailored quotation.
TECHNICAL DATA
Specifications
Values below follow the supplied product listing. Confirm the final selected configuration before ordering.
Product specifications
| Model | 6018C |
|---|---|
| Installation Type | Surface-mounted |
| Lifting Capacity | 4000 kg |
| Runway Length | 4500 mm |
| Runway Width | 630 mm per runway |
| Motor Power | 2.2 kW |
| Power Supply | 220 V / 380 V options; confirm phase and frequency |
| Control Voltage | 24 V |
| Drive System | Electro-hydraulic |
| Alignment Features | Front turnplates and rear slip plates |
| Secondary Lifting | Optional rolling bridge jack |
Installation requirements
Surface-mounted installation. Confirm final overall dimensions, minimum and maximum platform heights, runway spacing, ramp approach, concrete and anchoring requirements using the current factory drawing. Check vehicle ground clearance, overhead clearance and space around the control cabinet. Specify voltage, phase and frequency, and confirm any compressed-air requirements for the selected configuration.
PRODUCT DETAILS
Features, construction, and applications
Review the available product detail images for the selected equipment.
View 2 more detail images
PRODUCT VIDEO
See the equipment in detail
Play the product video directly on this page.
MODEL SELECTION
How to choose this equipment
Selection guidance
- Vehicle fit and alignment layout
- Check total vehicle weight against the 4000 kg main-lift rating, and match wheelbase and track width to the 4500 x 630 mm runways. Confirm the aligner, turnplates and rear slip-plate arrangement.
- Optional wheel-free lifting
- Specify whether a rolling bridge jack is needed. Confirm its separate rated load, lifting range, support-pad positions and suitability for the vehicles being serviced.
- Surface installation and power
- Provide bay dimensions, vehicle approach and available electrical supply. Confirm the latest installation drawing, concrete and anchors, platform heights, voltage, phase and frequency.
BUYER SEARCH GUIDE
Surface-mounted alignment scissor lift sourcing guide
The 6018C supports passenger-car wheel alignment, inspection and underbody service. A suitable optional rolling jack enables wheel-free work at approved lifting points.
Common sourcing language
Importers, distributors, and workshop buyers may describe BAOHUA 6018C 4T Ultra-Thin Wheel Alignment Scissor Lift using these related terms:
- wheel alignment scissor lift
- surface-mounted alignment lift
- ultra-thin scissor lift
- 4 ton alignment lift
What to compare before ordering
Compare the 4000 kg main capacity, 4500 x 630 mm runways, front turnplates, rear slip plates and optional rolling jack. Confirm vehicle fit, approach ramps, platform heights, floor and anchoring requirements, and the alignment-system layout.
View Car Lifts
Compare related models and choose the configuration that matches your vehicles, process, utilities, and workshop layout.
View categoryBUYER FAQ
6018C wheel alignment scissor lift FAQ
Review the confirmed product data and the project information needed before requesting a final configuration.
What is the 6018C lifting capacity?
The main lift is rated at 4000 kg. Any optional rolling jack has a separate rating that must be confirmed for the selected accessory.
Is this lift surface-mounted or in-ground?
The 6018C shown here is a surface-mounted, ultra-thin scissor lift. Plan the concrete floor, anchors, approach ramps and working clearances using the final installation drawing.
What are the runway dimensions?
Each runway is 4500 mm long and 630 mm wide. Confirm overall dimensions, runway spacing and platform heights for the final configuration before preparing the workshop.
Is the rolling jack included as standard?
The supplied product sheet describes the secondary rolling jack as optional. Include it in the quotation when wheel-free service is required, and confirm its capacity, lifting range and support arrangement.
Does the lift include a wheel alignment machine?
The lift provides front turnplates and rear slip plates for alignment work. The alignment measuring machine, targets and clamps are separate equipment unless expressly included in the quotation.
What power supply does the lift need?
The documentation lists a 2.2 kW drive, 24 V controls and 220 V / 380 V supply options. Specify the required voltage, phase and frequency when ordering.
What should I provide for a quotation?
Send vehicle weights and dimensions, workshop bay size, alignment-system information, electrical supply, rolling-jack requirements, quantity and delivery destination.